ResMed AirFit P10
A lightweight nasal pillows mask with a woven mesh QuietAir vent and split-strap elastic headgear. It is one of the smallest and quietest masks ResMed makes and comes with three pillow sizes in the box. No magnets.
Usually suits
- Nose breathers at lower to moderate prescribed pressures
- People with facial hair or claustrophobia who want minimal contact
- People who wear glasses or read in bed
Design
- Nasal pillows that seal at the nostrils
- Woven mesh QuietAir vent rated at 21 dBA
- Adjustable split-strap elastic headgear
- Short flexible tube
- Minimal frame with a wide field of vision, compatible with glasses
- Rated for 4 to 20 cm H2O
- No magnets
Strengths and trade-offs
- Very little contact with the face, nothing on the bridge of the nose
- Three pillow sizes in the box
- No magnets
- Simple, light headgear
- Rated only up to 20 cm H2O, and pillows can feel forceful at higher pressures
- Can cause nostril soreness if the pillows are too small or pushed in
- Standard version is not compatible with AirMini (a separate P10 for AirMini kit exists)
- Nasal only, so mouth breathing causes leaks without a chinstrap
Finding your size
The standard pack includes Small, Medium and Large pillows, so you size by trying them. Start with the size that sits just at the opening of your nostrils without pushing inside; the pillows should seal at the rim, not fill the nostril. If Small is still too large, an Extra Small cushion is sold separately, and the For Her version ships with Extra Small, Small and Medium.
How to fit it
Start with Medium
Fit the Medium pillows first. They should rest at the nostril openings, angled slightly back toward the head, without being pushed up into the nose.
Put on the headgear
Hold the pillows in place and pull the headgear over your head. Separate the split straps at the back so one sits higher and one lower on the back of your head for stability.
Adjust gently
With the machine running, adjust the elastic headgear just enough to keep the pillows seated. Too much tension pushes the pillows into the nostrils and causes soreness.
Compare sizes
If air escapes around the pillows, try the next size up; if they feel like they are filling your nostrils, go down a size. Keep the size that seals with the least pressure.
Common problems and fixes
Sore or irritated nostrils
Loosen the headgear and recheck the size; pillows that are too small get pushed in. Nasal pillow liners or a saline spray may help dryness. Persistent sores are a reason to talk with your clinician.
Whistling at the nostrils
A whistle usually means a small leak at the pillow rim. Reseat the pillows, check the angle, and try the next size.
Dry nose
Pillows direct air straight into the nostrils. Using your machine's humidifier and heated tubing (adjusted in the comfort menu) can help, along with saline spray or a CPAP-safe nasal moisturizer.
Mouth leaks
Try a chinstrap. If you keep breathing through your mouth, ask your clinician about a full face or under-the-nose full face mask.
Cleaning and care
Every day, hand wash the pillows, frame and tubing in warm water with mild soap and clean the vent with a soft bristled brush. Hand wash the headgear weekly. Rinse each part under running water, dry the vent with a clean towel and air dry everything away from direct sunlight. ResMed notes the vent may discolor over time and that this is not a safety concern. Do not use ozone or UV cleaning devices.
How often to replace parts
- Mask
- 1 complete mask every 3 months (Medicare A7034, nasal interface).
- Cushion
- Up to 2 sets of pillows per month (Medicare A7033). This is typical insurer guidance; replace sooner if a pillow tears or stops sealing.
- Headgear
- 1 every 6 months (Medicare A7035).
Supplies that can help
A soft strap that supports the jaw to help keep the mouth closed, used mainly with nasal and nasal pillow masks to reduce mouth leaks.
Salt water spray that moistens and clears the nose, a simple aid for the congestion and dryness some people get on CPAP.
A water-based or saline gel applied inside or around the nostrils to soothe dryness and soreness from CPAP airflow.
Tubing with a built-in heating wire that keeps humidified air warm all the way to the mask, which is the main fix for rainout (water droplets …
Pre-moistened wipes for a quick daily wipe of the mask cushion, mostly to remove skin oils between proper washes.
Retailer links are affiliate links. We may earn a commission at no cost to you.
Frequently asked questions
What pressure can the AirFit P10 handle?
ResMed lists a range of 4 to 20 cm H2O. If your prescribed pressure is above that, or the air feels harsh in your nose, ask your clinician or supplier about other mask types.
Which pillow size comes with the AirFit P10?
The standard pack includes Small, Medium and Large pillows. Extra Small is sold separately, and the For Her pack includes Extra Small, Small and Medium.
Why does my AirFit P10 vent look discolored?
ResMed says the woven mesh vent may discolor over time and that this is not a safety concern. Replace the mask on schedule or if the vent is damaged.
Can I use the AirFit P10 with an AirMini?
Not the standard version. ResMed sells a separate AirFit P10 for AirMini setup pack designed for that machine.
Sources
Last reviewed October 11, 2026. How we research · Report an error